Search results for "Impedance measurement"
showing 10 items of 11 documents
Evaluation of Esophageal Motility Using Multichannel Intraluminal Impedance in Healthy Children and With Gastroesophageal Reflux
2010
Abstract OBJECTIVE: : Multichannel intraluminal impedance (MII) directly evaluates esophageal bolus transport. There is a good correlation between MII and manometry in healthy adults, but there are no reports concerning children.The aim of the present study was to determine normal values of esophageal motility using only impedance measurements in healthy children and in a pediatric population with gastroesophageal reflux (GER). PATIENTS AND METHODS: : We described in the present study 60 children submitted to pH-MII for 24 hours for suspected GER. Patients were divided into 2 different groups on the basis of their pH-MII report. Group 1 patients showed acid GER, whereas group 2 patients had…
A Line Impedance Calculator Based on a G3 PLC Modem Platform
2022
Power line communication (PLC) is one of the most today used technologies for both automatic meter reading and many other smart grid applications. In this framework, a characterization of the electrical network in the PLC frequency range is needed in terms of impedance measurement and received signal level. This can allow choosing the most suitable and less noisy frequency ranges for PLC transmission. Usually, these characterization measurements are performed with dedicated instrumentation and in the absence of mains voltage. This article wants to propose an alternative solution, which allows these kinds of measurements to be performed using electronic boards currently used as on-field appl…
Monitoring of Rouging and De-Rouging of Stainless Steel for Chemical Reactors by Photoelectrochemical and Impedance Measurements
2016
The food and fine-chemical industry has for a long time been troubled by red brown to dark violet deposits in distillation columns, storage vessels and distribution systems for purified water and clean steam. Owing to the visual appearance of those deposits, the phenomena was referred as rouge. Although formation of rouge, i.e. rouging, is a commonly known phenomenon in stainless steel systems, the basic mechanism is still not fully understood. The phenomenon causes precipitation of iron as fine red-brown ferric oxide or hydroxide particles. Moreover adherent discoloration of the stainless steel surface is often observed in conjunction with the loosely adhered rouge particles. The affected …
A Technique for Power Supply Harmonic Impedance Estimation Using a Controlled Voltage Disturbance
2002
A method for power system impedance estimation is presented. The method employs a power converter to inject a voltage transient onto the supply system. As the technique employs controlled power electronic devices it may be used as a stand alone piece of a portable measurement equipment, or it may be embedded into the functions of an active shunt filter for improved harmonic control. The impedance is estimated through correlation of the measured voltage and current transients. Simulations and experimental results demonstrate the measurement technique is highly accurate and effective.
Design and Development of a Labview Application for the Measurement of the Complex Impedance of a Fuel Cell in Real Time
2014
International audience; To optimize the performance of fuel cells and to deepen the knowledge of their behavior, it is necessary to make measurements in real time. To run such a measure, it is necessary to use specific software and hardware tools to instrumentation fuel cells. In this context, we presented the steps of designing and developing an application for the measurement of the complex impedance by electrochemical impedance spectroscopy method (EIS) using LabVIEW® software. The experimental results are obtained using a Ballard Nexa® PEM fuel cell, an electronic load produced in our laboratory and application developed by the LabVIEW® software.
Wideband modeling of cascaded H-plane waveguide junctions using the generalised impedance matrix representation
2009
A strong interest in H-plane waveguide components composed of a large number of cascaded planar junctions is recently renewed. Therefore, the more efficient development of full-wave analysis tools of such devices is again receiving consideration, specially for its potential use within modern design tools. A novel technique for providing the wideband generalised impedance matrix representation of the inductive devices in the form of pole expansions, thus extracting the most expensive computations from the frequency loop is proposed. For such purpose, the whole device is first decomposed into simpler building blocks, i.e. planar junctions and uniform waveguides, which are modelled in terms of…
Electromechanical coupling in anodic niobium oxide: Electric field-induced strain, internal stress, and dielectric response
2012
Seemingly, contradictory results have been reported so far for electrostriction in anodic oxides. Furthermore, no definitive agreement could be obtained with theory. In this paper, in situ techniques are combined to elucidate electrostriction in anodic niobium oxide. The dependence of strain, internal stress, and dielectric constant on the electric field is measured by, respectively, spectroscopic ellipsometry, curvature, and impedance measurements. The through-thickness strain is tensile and proportional to the square of the electric field. The in-plane internal stress is compressive and proportional to the square of the electric field at low field values. The internal stress is predicted …
Electrochemical Fabrication and Physicochemical Characterization of Metal/High-k Insulating Oxide/Polymer/Electrolyte Junctions
2014
Photoelectrochemical polymerization of poly(3,4-ethylenedioxythiophene), PEDOT, was successfully realized on anodic film grown to 50 V on magnetron sputtered Ti-6 atom % Si alloys. Scanning electron microscopy allowed us to evidence formation of compact and uniform polymer layers on the oxide surface. Photoelectrochemical and impedance measurements showed that photopolymerization allows one to grow PEDOT in its conducting state, while a strong cathodic polarization is necessary to bring the polymer in its p-type semiconducting state. Information on the optical and electrical properties of metal/oxide/polymer/electrolyte junctions proves that PEDOT has promising performance as an electrolyte…
Characterizing archaeological bronze corrosion products intersecting electrochemical impedance measurements with voltammetry of immobilized particles
2017
Application of electrochemical impedance measurements to microparticulate deposits of copper corrosion products attached to graphite electrodes in contact with 0.10 M aqueous HClO4 electrolyte is described. The impedance measurements were sensitive to the applied potential and the amount of solid sample and were modeled taking into account the contribution of the uncovered base electrode. Several pairs of circuit elements provide monotonic variations which are able to characterize different corrosion compounds regardless the amount of microparticulate solid on the electrode. Application to a set of archaeological samples from the archaeological Roman site of Gadara (Jordan, 4th century AD) …
Influence of Anodic and Thermal Barrier Layers on Physicochemical Behavior of Anodic TiO2 Nanotubes
2011
Electrochemical and photo-electrochemical behavior of self-organized TiO2 nanotubes formed in organic solvents have been studied by taking into account the formation of new barrier layers beneath nanotubes either due to the anodic polarization in aqueous solutions or air exposure during high temperature annealing. It has been shown that before annealing, electrochemical and photoelectrochemical answers are dominantly controlled by the physicochemical properties of the anodic barrier layer. Annealing in air at sufficiently high temperatures changes the initial amorphous structure of as-prepared nanotubes and forms a new oxide layer below them due to thermal oxidation of underneath titanium. …